FAQ Stencil Removal

  1. Q1: Why isn't my stencil remover working?
  2. Q2: How should I use stencil remover?
  3. Q3:
  4. Q4: Can I used bleach to reclaim my mesh?


Q1:Why isn't my stencil remover working?

It is very important to never let the stencil remover dry. It locks the stencil in the mesh with a permanent chemical bond.

Under exposed stencils are harder to remove than completely cured/exposed stencils.

Under exposed means some of the sensitizer did not cross link. This is always on the inside of the stencil because invisible UV energy didn't have enough time to move all the way through the stencil to the inside. Penetration of UV energy is not 'linear'. The deeper the UV energy has to penetrate, the longer it takes based on the physics rule called the Inverse Square Law. If you double a distance energy has to travel, it takes 4 times the energy - NOT double. Many low energy UV lamps may never penetrate a thick stencil.

When you spray stencil remover on the stencil, it has to penetrate and attack the chemical crosslinks formed by UV exposure. No crosslinks - no easy stencil removal.

The stencil remover chemical creates another reaction with under-exposed stencil and forms a chemical bond with the mesh that is very difficult to remove.

Q2: How should I use stencil remover?

To remove a stencil from the mesh. A chemical is applied to a stencil that breaks apart the basic chemicals that were mixed together and cross linked when they were exposed with Ultra Violet light. The proper de-coating chemical works like a key in a lock and the stencil falls off the mesh and washes down the drain.

Q3: ?

Penetration
Fully, or even over exposed screens, actually reclaim easier than under exposed screens.
Screen makers under-exposure to keep fine lines fro closing up and choking the actual ink print. Under exposure does reduce that problem, but at the cost of stencil durability and the ability to reclaim the stencil.

Many reclaiming problems result from mistakes made earlier, during the stencil-making process. Chief among these is underexposing the emulsion. Underexposed emulsion can be virtually locked to the threads of the mesh and may resist all efforts to reclaim it. The solution is to buy and learn how to use an exposure calculator or 21 Step Gray scale to measure stencil hardness.



We 2 general videos on capillary film and direct emulsion under the 'general' tab. Watch those movies to learn how to reclaim a stencil
My stencil doesn't want to reclaim

Q4: Can I used bleach to reclaim my mesh?


Bleach
I've discussed your question about using bleach as stencil remover with our senior chemist. He says that bleach is both slower than SMP and environmentally harsher.

Controlling the dilution of bleach as it contacts the stencil during decoating is difficult. If the concentration is too high, there's danger of a lock-in from an oxidation-reduction reaction; too low a concentration, and there's no effect.

The optimal concentration varies for each emulsion blend. Certain types of emulsion, such as 925WR, are hard to reclaim with bleach of any concentration.

So there it is: bleach is slower, less green and, most importantly, considerably less reliable than SMP.



The most common reclaim chemical in the screen industry is sodium metaperiodate. This is a salt that is related to household chlorine bleach, but without the harmfull characteristics associated with bleach.

Typical emulsion removers contain sodium metaperiodate or salts of periodic acid.

Problems during decoating or reclaiming of the screen occur when the screen was underexposed or if the emulsion is extremely water resistant. Solvents may cause underexposed emulsion to harden and "lock in", resulting in difficult reclaiming and excessive emulsion haze. The higher the water resistance often emulsion the more difficult it is to reclaim. Emulsion that is only solvent resistant should reclaim easy. Never let the reclaimer dry on the screen.

Why am I having trouble reclaiming? The old emulsion wonít come off the screen. Many things can cause reclaiming trouble. The most common cause, however, is underexposure of the stencil and/or under cured emulsion. If the emulsion is not completely dry before exposure, the soft, wet emulsion remains inside the dried outside surface like a sandwich. This uncured emulsion will react with inks, solvents and other chemicals during the printing process and chemically lock onto the screen. This will make it very hard to reclaim the screen later. Other factors that promote easy reclaiming are proper exposure and cleaning the ink completely and then removing the ink wash with degreaser. Lead with - The basics of cross linking


Reclaiming The reclaiming problems are one of the biggest culprits of improperly exposed screens. If a screen is underexposed the subsequent stencil will have good detail but will be soft or slimy. This soft stencil will not reclaim as easily because any solvents in the ink mix with the soft emulsion and stain the mesh. If a screen should need to be underexposed for some reason always be sure to post expose the screen after it is washed out and dried. While this can be accomplished by placing the screen back on the exposure unit and exposing without the film positive, it is often just as easy to place the screen in the direct sun-light for a few minutes. Locked by chemical which is NOT breakable

Difficult reclaiming if Under exposed
Mixing stronger is not necessairly better.
Only a minor amount of the Sodium Metaperiodate in reclaimers is needed to breakdown the stencil. The large amount of water is what allows the chemicals in reclaimer to penetrate the emulsion coating so they can do their job.

Stencil remover has little effect on 'underexposed' stencils. The sodium metaperiodate in stencil remover attacks the cross links that hold the stencil in the mesh. If you underexposed, there aren't lots of links to break, and you have to use brute force to punch the stencil from the mesh, instead of the smooth breakdown of the stencil like turning a key in a lock.

So fully harden your stencil, mix reclaimer properly and apply as directed, and absolutely use the power washer to blast it off after the reclaimer breaks it down.


The longer a stencil remains in a screen the harder the emulsion is likely to become. Get in the habit of reclaiming your screens as soon as you are finished with them. Emulsions can also become excessively hardened through contact with certain strong solvents. If your exposures are bang on and youíre still running into reclaiming problems, try switching to a different wash-up or screen-opener.

Sometimes stubborn bits of stencil hang on despite your best efforts. Try reapplying the stencil remover or dehazer to that spot. Wait a few minutes and hit it with your pressure washer. Adjust the nozzle to deliver a more finely focused spray. Remember that as the water jet becomes narrower its power increases. Donít let it stay aimed at one small area. Keep it moving.

Although, we've talked mostly about direct emulsions, the reclaiming process for films is similar. In fact, films can be easier to reclaim. Just remember that indirect films are gelatin-based and require the use of special stencil removers.