Stencil Remover

Stencil Remover Liquid No. 4

Ready-to-use stencil liquid remover for fast and thorough removal of direct emulsions, CDF Direct-Films, and Pulsar indirect film from all types of mesh including metalized polyester.

Will not etch mesh; contains no strong alkalis or hypochlorites. Ideal for use in tanks: will not attack adhesives on stretch and glue frames; tank heating unnecessary. Odor free

    Instructions
  1. Remove ink with the proper solvent.
  2. Use Screen Degreaser Liquid No. 3 to remove solvent residues and to help speed the action of the stencil remover. Rinse thoroughly.
  3. Use a soft brush to apply Stencil Remover Liquid No. 4 on the screen from both sides.
  4. Wait five minutes - no longer. Do not allow the stencil remover to dry on the screen, as this can result in a permanent stencil.
  5. Wash away the stencil with a hard spray of water, preferably a power spray.
  6. Tank method: Dilute Stencil Remover No. 4 with water (no more than 1:2) - but only after thorough testing. It is recommended, however, that Ulano No. 4 be used at full strength for fastest and most thorough stencil removal.

Stencil Remover Liquid No. 4 is a strong oxidant. It can cause skin irritation; use gloves. Keep the container closed tightly. Clean spills immediately.

First Aid: In case of contact with the eyes or skin, flush immediately with water. If irritation develops, contact a physician.

Stencil Remover Concentrate No. 42 1:50

buttonTech Data SheetbuttonTech Data Sheet- Spanish

Concentrated liquid stencil remover for fast and thorough removal of direct emulsions, CDF Direct Films, and Pulsar indirect film from all types of mesh including metalized polyester.

    Instructions
  1. Dilute one part Stencil Remover Concentrate No. 42 with 50 parts water.
  2. 400ml yields approximately 5 gallons (18.93 l - 1 gallon yields approximately 50 gallons.
  3. Clean ink from stencil. 
  4. Brush the liquid onto both sides of the screen. 
  5. Let screen stand for no more than 5 minutes.
  6.   Rinse with a hard cold water spray. 
  7. The use of a power spray is preferable after the chemical has been rinsed off with a normal spray.
Health and Safety Information:

Stencil Remover Concentrate No. 42 is a strong oxidant and corrosive.  Contact with combustible material may cause fire.  Causes burns.  In case of contact with eyes, rinse immediately with plenty of water and seek medical advice.  Remove contaminated clothing immediately.  After contact with skin, wash immediately with plenty of water.  Wear suitable protective clothing, gloves and eye / face protection.  In case of accident or if you feel unwell, seek medical advice immediately.

Stencil Remover Powder No. 44 - Concentrated Powder

Mix your own stencil remover and save money by not shipping water from Brooklyn. Perfect for dip tanks. Dissolve 2oz in 1 gallon of water. Use with all Ulano Direct-Emulsions, CDF® Direct-Films, and Pulsar indirect film. It is not effective on gelatin films (use Enzyme No. 1).

    Instructions
  1. Clean ink from stencil.
  2. Brush the liquid onto both sides.
  3. Let stand for no more than 5 minutes.
    Do not let any stencil remover dry on the mesh - it will lock the stencil in the mesh.
  4. Rinse off with a mild spray of water to prevent splashing the stencil remover.
  5. Rinse with a strong power water spray if necessary.
Health & Safety Information

Ulano No. 44 Stencil Remover Powder is a strong oxidant. Contact with combustible or flammable material can cause fire. It can cause skin and eye irritation. Use gloves and goggles. Clean spills immediately.

First Aid: In case of contact with the eyes or skin, flush immediately with water for at least 15 minutes. If irritation develops, contact a physician.

Stencil Remover Paste No. 5 - Ready to use stencil remover paste

Product Fact Sheet Tech Data Sheet buttonTech Data Sheet- Spanish
MSDS

Ready-to-use paste for fast and thorough removal of direct emulsions, CDF Direct Films, and Pulsar indirect film from all types of mesh including metalized polyester.

    Instructions
  1. Remove ink with the proper solvent.
  2. Degrease first with Screen Degreaser Liquid  No. 3 to remove solvent residues and to help speed the action of the stencil remover. Rinse thoroughly.
  3. Use a soft brush to apply Stencil Remover Paste No. 5 on the mesh from both sides.
  4. Wait five minutes - no longer. Do not allow the stencil remover to dry on the screen, as this can result in a permanent stencil.
  5. Wash away the stencil with a hard spray of water, preferably a power spray.
  6. Note: Avoid freezing Stencil Remover Paste No. 5. Freezing and thawing will change the consistency from a paste to a liquid. This has no effect on the chemical activity as a stencil remover - it can be used in the same way as Stencil Remover Liquid No. 4.
Health & Safety Information

Stencil Remover Paste No. 5 is a strong oxidant. It can cause skin irritation; use gloves. Keep the container closed tightly. Clean spills immediately.

First Aid: In case of contact with the eyes or skin, flush immediately with water. If irritation develops, contact a physician.

Enzyme No. 1 - Gelatin Stencil Remover

Product Fact Sheet Tech Data Sheet MSDS

A safe enzymatic product especially formulated for thorough removal of gelatin-based indirect photostencils from all types of mesh with all Indirect Films except Ulanolux UP3. Odor free.